MOVE

Logo MOVE
MOVE
MOVE with BrainAmp
  • Converts any existing amplifier/electrode combination into a wireless solution

  • Each MOVE is capable of handling up to 64 channels

  • Up to 5 units can be used in the same location

  • Comes with rechargeable lithium-ion batteries allowing for 10 h operation time

MOVE: Converts your recording setup into a wireless system

The wireless MOVE is a solution that replaces the existing cables connecting electrodes and amplifier with wireless-based communication. This solution allows the subject to move freely and makes it very suitable for use with a Brain Computer Interface (BCI), neurofeedback and motor learning.

The small, lightweight transmitter and the receiver can be used with virtually any existing amplifier/electrode combination. As the transmitter is not integrated into the cap, there is no risk of damaging it when cleaning the cap. Simply disconnect the transmitter and clean the cap the way you always have.

Each MOVE is capable of handling 64 channels; up to 5 units can be used in the same location. With this solution normal experiments become more convenient and new paradigms can be incorporated into day-to-day research.

The MOVE transmitter amplifies and digitizes the incoming raw analogue signal and sends it to the MOVE receiver, where the digital data is converted back to analogue. Since the amplification factor is 1, the existing EEG amplifier receives exactly the same data as previously. If the data is not received properly, the receiver unit will send a TTL pulse marker to the amplifier. A further marker is sent when stable and reliable data reception resumes. This feature is extremely useful during the data analysis stage; in the unlikely event of the wireless connection being interrupted during the recording, a user can still determine exactly when the problem occurred.

YouTube

By loading the video, you agree to YouTube's privacy policy.
Learn more

Load video

MOVETechnical specifications
General specifications
RF frequencyISM band, 2.4 to 2.5 GHz, 2 switchable frequencies.
Every transmitter/receiver belongs to one of the following switchable requency groups. The group is indicated by a capital letter (A-D) in the serial number:
A: 2,402 MHz / 2,490 MHz
B: 2,406 MHz / 2,494 MHz
C: 2,410 MHz / 2,498 MHz
D: 2,414 MHz / 2,482 MHz
Please observe any differing national regulations (e.g. USA).
Data encodingPCM, 16 bits/channel, CRC16 data checking
Signal transit time4.4 ms
Transmission speed2 Mbit/s or 1 Mbit/s, switchable
Sampling rate954 Samples/s at 2 Mbit/s, 508 Samples/s at 1 Mbit/s
Receiver
Channels32 or 64 analog
D/A converterBit width: 16 bit
Gain1 (1:1 transmission of transmitter input to receiver output)
Output filter250 Hz 3-pole Butterworth
Power supply3.7 V, 720 mAh (2.66 Wh)
Type: DURACELL DRC4L, rechargeable lithium-ion battery changeable
ChargingExternal battery charger (Canon®)
On switchRocker switch
Battery deep discharge protectionYes
Power consumption50 mA (typical)
Operation time10 hrs with fully charged battery
Dimensions (H x W x D)68 mm x 160 mm x 187 mm
Weight590 g (without antennas)
Antennas2 (attachable)
Digital interfaces1 x isolated trigger port
Transmitter
Channels32 or 64 referential inputs
unipolar
A/D converterBit width: 18 bit
Resolution: 100 nV
Input voltage range±3.276 mV
DC offset tolerance±140 mV
Common-mode rejection (CMR)> 90 dB
Input resistance> 10 MOhm
Impedance measurementNo
Filter properties0.16 Hz / 10 s
Antialiasing filter250 Hz 3-pole Butterworth, low-pass
Carrier frequency2.461 GHz / 2.471 GHz
RF output power0 dBm
Noise1 μVpp
Power supply3.7 V, 720 mAh (2.66 Wh)
Type: DURACELL DRC4L, rechargeable lithium-ion battery changeable
Operation time10 hrs with fully charged battery
Charging External battery charger (Canon®)
On switchRocker switch
Battery deep discharge protectionYes
Power consumption40 mA (typical)
Dimensions (H x W x D)42.2 x 48.2 x 60 mm
Weight116 g
AntennaIntegrated in the housing
RangeApprox. 6 m
Miscellaneous
Suitable for use in MR scanner roomNo
Medical deviceNo
Receiver / TransmitterTested under the FCC Certification Rules contained in Title 47 of the CFR, Parts 15 Subpart B & ICES-003 for Class B Digital Devices.
The equipment has been tested and certified under Industry Canada RSS-210, Issue 8, December 2010 RSS-GEN, Issue 3, December 2010
CE markingNot labelled with a CE mark anymore (as of June 2016)
FCC identification numberFCC ID: ZCZMOVE 2011

Recommended add-ons

actiCHamp Plus & PowerUnit

actiCHamp Plus

BrainAmp w. PowerPack and BUA

BrainAmp