STE compact for LiveAmp

  • Extends your mobile setup with physiological signals and trigger options
  • Adds 6 AUX sensor inputs plus input for pulse oximetry
  • Enables 8-bit wired or wireless triggering
  • Provides flexible powering options for light setups and long recordings
STE compact for LiveAmp : Enhance your mobile EEG measurements

STE stands for Sensor and Trigger Extension. Combining the LiveAmp with the STE compact makes it possible to add additional physiological signals to your mobile EEG research. All of this, thanks to the internal memory of the LiveAmp amplifier, is completely independent from a recording computer.

The additional inclusion of sensor signals into your mobile EEG research with the LiveAmp is as easy and flawless as 1, 2, 3. Just connect the STE compact to the LiveAmp from one side. Thanks to the included belt clip, you can easily connect the STE compact to the subject or the LiveAmp Mobility Set.

Sensors

The STE compact has six auxiliary (AUX) sensor inputs. These can be used for attaching a Photo Sensor for stimulus presentation timing from a display, a Force Sensor for heel strike detection, a Respiration Belt, or a GSR Sensor to name just a few. All Brain Products sensors currently on the market are compatible with the STE compact.

In addition to the AUX inputs, there is a dedicated digital input to connect a Pulse Oximetry Sensor, which allows you to record SpO2 (blood oxygen saturation), HR (heart rate), PPG (photoplethysmogram).

Triggering

STE compact comes with a built-in Wireless Trigger Receiver, ready to be paired with its transmitter counterpart. Our Wireless Trigger solution offers reliable (+/- 1 sample), low latency (~2.5 ms) trigger transmission across 10 m distance.

Note: Wireless Trigger allows you to connect one Trigger Transmitter (trigger source) to several (up to 5) Trigger Receivers/STE compacts for hyperscanning setups.

A wired 8-bit trigger connection is also possible by means of a 9-pin D-Sub connector.

Power supply

STE compact comes with internal, exchangeable standard AA batteries, with which it can run for up to 10 hours. When every gram counts, the STE compact can be powered by the connected LiveAmp only. You can even exchange batteries while recording (“hot swapping”) and continue without interruption. For longer and less-supervised measurements, the operation time can be extended via an additional power bank.

STE compactTechnical data
Number of AUX channels6
AUX channels are not intended to measure EEG/ExG signals directly.
Input range of AUX channels±4.8 V
Sampling rate of AUX inputsThe sampling rate is the same for all LiveAmp and STE compact channels. Regarding channel numbers and sampling rates the same restrictions as mentioned for LiveAmp apply.
Power supply at AUX inputsVoltage: ± 5 V
Current: Max. total current of 60 mA (that is, either 1 x 60 mA or 6 x 10 mA etc.)
Galvanic isolation of AUX inputsAUX channels are galvanically isolated from the EEG/ExG channels of LiveAmp (isolation voltage 1,500 VAC, 50 Hz).
Number of Trigger In bits8
Trigger InCable
- Connector: 9-pin female D-Sub; pin assignment: see below
- Low active (internal pull up resistor (10 kOhm) to Vcc)
- TTL (LVTTL) signals, 0 to +5 V (+ 3.3 V)
- Can be used alternatively to Wireless Trigger In

Wireless
Wireless module built-in. Can be used alternatively to cable Trigger In.
Galvanic isolation of trigger inputsTrigger channels are galvanically isolated from the EEG/ExG channels of LiveAmp (isolation voltage 1,500 VAC, 50 Hz).
Power consumptionMax. 0.9 W
Dimensions (W x D x H)12.3 cm x 7.6 cm x 2.6 cm
Weight< 130 g
Power supply- Usually: via two removable AA batteries (in the STE compact battery compartment)
- If batteries in the STE compact are discharged and no power bank is connected: via LiveAmp
- If power bank is connected: via power bank
Length of cable to LiveAmp80 cm
Required LiveAmp revisionLiveAmp Rev. 04 or higher and LiveAmp FW Version 4.77 (can be installed as of LiveAmp Rev. 04) or higher.
Miscellaneous
Suitable for use in MR scanner roomNo
Medical deviceNo
CE markingThe Brain Products GmbH confirms the electromagnetic compatibility (EMC) of this product according to the DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member States relating to electromagnetic compatibility.

The Brain Products GmbH confirms the RoHS compliance of this product according to Directive 2011/65/EU of the European Parliament and the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (recast published in the Official Journal of the European Union on 1 July 2011) as well as all its amendments up to and including the Commission delegated directive (EU) 2015/863 of 31 March 2015 (published in the 0fficial Journal of the European Union on 4 June 2015).

Getting started

You are currently viewing a placeholder content from YouTube. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.

More Information

Recommended add-ons

LiveAmp

LiveAmp

LiveAmp Wireless Trigger

Wireless Trigger

TriggerBox Plus

TriggerBox Plus

Sensors for the lab environment

Sensors for the lab environment

LabSim

LabSim

BrainVision Analyzer

BrainVision Analyzer